Rubber & Plastic Products

Most Natural Pigments Survive PLA and PBS Compounding, but UV Stability Still Limits Their Use

A study of spirulina, curcumin, beetroot and chlorophyllin masterbatches in two biodegradable polyesters finds conventional processing workable, with lightfastness the remaining obstacle.

Farida NasrNovember 2, 20265 min read1 views
Four differently coloured polymer strands leaving a twin-screw extruder beside dishes of natural pigment powder and translucent biopolymer pellets on a laboratory bench.

Researchers have tested whether four commercial natural colorants can be carried through industrial melt processing in biodegradable polyesters without losing their colour, flow behaviour or mechanical performance. The work, set out in the study "Sustainability in the Development of Natural Pigment-Based Colour Masterbatches and Their Application in Biopolymers," combined blue spirulina, yellow curcumin, red beetroot and green chlorophyllin with polylactic acid (PLA) and polybutylene succinate (PBS).

Each pigment was compounded into a colour masterbatch on a twin-screw extruder, with titanium dioxide, calcium carbonate and stearic acid added to the formulation to support UV protection, dispersion and processing. The masterbatches were then let down into the matching polymer at 2, 4 and 6 wt% and injection moulded into test specimens.

Thermal window sets the limits

Heat is the central constraint, because the organic structures of natural pigments can begin to degrade at lower temperatures than the polymers they are meant to colour. Thermogravimetric analysis put degradation onset at approximately 229 °C for spirulina, 244 °C for curcumin, 258 °C for chlorophyllin and 267 °C for beetroot, while PLA and PBS degrade at considerably higher temperatures.

To bridge that gap, the team selected extrusion profiles that melted each polymer while limiting thermal exposure of the pigments: 145 °C for PBS and 190 °C for PLA, run at 65 rpm with a feed rate of 2 kg/h.

Spirulina fails in PLA

The chosen processing window suited most pigment–polymer combinations, with one clear exception. Spirulina lost its characteristic blue colour during PLA processing, so no blue PLA masterbatch could be produced. Because PBS melts at the lower temperature, the same pigment retained sufficient stability to be compounded successfully — an illustration that compatibility depends strongly on the thermal requirements of the matrix rather than on the colorant alone.

Flow and mechanics hold steady

Rheologically, the pigments caused only limited change. Melt flow rate fell slightly, indicating a modest rise in melt viscosity: neat PLA measured about 50 g/10 min and its natural-pigment masterbatches stayed close to that value, while PBS showed a similarly minor reduction. For compounders the practical implication is that conventional screw design, pressure settings and moulding conditions handled most formulations without major problems.

Mechanical testing across the 2 to 6 wt% range showed no significant losses. PLA started from a Young's modulus of about 1710 MPa and tensile strength of 65.6 MPa; PBS from roughly 392 MPa and 34.5 MPa. The coloured formulations stayed close to those baselines, and impact strength remained within a similar range, although individual pigments produced some variation.

Colour fastness is the open question

Successful extrusion did not guarantee durable colour. After 50 hours of xenon-lamp exposure, most formulations showed a colour difference above ΔE* = 2, a visually perceptible shift. The leading exception was a PLA formulation containing 2 wt% green chlorophyllin masterbatch, which showed the highest photostability.

The study therefore identifies UV stability as the largest barrier to broader use. Packaging, consumer products, agricultural parts and outdoor applications may require additional stabilization, protective coatings or pigment modification before natural colours can compete with conventional systems over long service periods.

Lower carbon footprint

The environmental comparison favoured the bio-based colorants. Under the study's assumptions, one kilogram of curcumin pigment generated about 0.04 kg CO2-eq, against 18.65 kg CO2-eq for the inorganic green reference pigment. The natural-pigment masterbatches also consumed less electricity during extrusion and pelletizing.

The researchers conclude that lightfastness and thermal stability still need development, but that several natural colorants can be compounded into PLA and PBS on conventional processing equipment with only limited changes to melt viscosity and mechanical performance.