Metals & Alloys

Zmag advances permanent-magnet stirring, pumping and scrap submergence for aluminum casthouses

Zmag America is promoting non-contact magnetic systems for furnace stirring, molten-metal circulation and scrap submergence as casthouses process more lightweight recycled feed.

Mireia SanchisNovember 10, 20265 min read0 views
A cutaway illustration shows a non-contact magnetic circuit beside a furnace pump well, creating a gentle vortex that draws lightweight aluminum scrap beneath the molten-metal surface.

Aluminum casthouses are under pressure to use more recycled metal without hurting melt quality, recovery rates or production efficiency. As operators add post-consumer recycled aluminum, lightweight scrap and machining chips are becoming more important, but these low-density materials are difficult to introduce into conventional melting furnaces. Efficient feeding and submergence are therefore essential, and Zmag America is developing permanent-magnet equipment for molten-metal circulation, furnace stirring and scrap recovery.

Zmag's approach is built on industrial magnets and magnetic circuits. The company traces its roots to magnetic engineering and eddy-current separation for recovering non-ferrous metals from mixed streams, and later expanded into molten-metal applications. Its patented zPMC (Zmag Permanent Magnetic Circuit) is the foundation for equipment that stirs, circulates and submerges material in molten aluminum.

Permanent magnets instead of immersed impellers

The distinction between permanent-magnet and conventional electromagnetic systems is central. Zmag says zPMC uses a permanent magnetic circuit to generate the field that moves molten metal, rather than a conventional electromagnetic stirring arrangement. The resulting movement is described as a “virtual impeller,” allowing circulation without conventional immersed mechanical impellers.

Conventional mechanical pumps are widely used but rely on immersed rotating components that can deteriorate through exposure to molten aluminum, dross accumulation and contact with refractory debris. Casthouses also need consistent temperature and chemical composition throughout the bath, so circulation equipment must support heat transfer and metal movement while limiting interruptions and excessive metal loss.

MagStir and MagPump

Zmag's MagStir is a non-contact stirring system for melting and holding furnaces. It uses the permanent magnetic circuit to generate movement in the molten bath and support homogenization of temperature and alloy composition. Configurations cover furnaces from 15 to 200 metric tons, and the non-contact design removes the immersed mechanical stirring component.

New Zealand Aluminium Smelters installed MagStir in a casting furnace and later extended its use to additional furnaces. A 2017 technical case study examined the installations and reported improvements in temperature control during furnace preparation. A MagStir unit was also fitted to a casthouse furnace at Rio Tinto-operated Boyne Smelters in Queensland, Australia, in 2019.

MagPump extends the magnetic approach to pumping and circulation. It fits a standard pump well without furnace modification, has no physical impeller and is marketed as a nearly hands-free alternative with no consumable parts and minimal downtime.

At TST Inc.'s TANDEM Division in Fontana, California, MagPump replaced a mechanical pump in a production furnace during a seven-week trial. The findings described smooth operation and reduced disturbance to the molten-metal surface. TST management also reported that the system avoided the splashing seen with conventional pumping as furnace metal level fell during draining. It was also presented at TMS 2023 for side-well, multi-chamber furnaces, with potential for gas injection and scrap submergence.

Typhoon targets chips and low-density scrap

Zmag's Typhoon system focuses on scrap submergence and chip melting. It introduces lightweight aluminum scrap and machining chips beneath the molten-metal surface rather than letting them remain at the top. Its magnetic circuit generates a vortex-like movement that draws material into the melt, supporting heat exchange and recovery during remelting.

At Neuman Aluminium's Marktl facility in Austria, Typhoon was added in a furnace modernization project to expand processing of low-density post-consumer scrap. The targeted material included lightweight fractions at about 375 kg/m³, which had challenged conventional charging and melting. Neuman targeted one metric ton per hour while continuing to melt solid charge in the same furnace. During operation, Typhoon processed almost twice the planned scrap quantity within the expected time without disrupting normal operations, according to the published account. Neuman also reported low operator involvement and no negative effect on melt or product quality.

According to the technical account, Typhoon operates at 5-15 kW including its air-cooling blower and can submerge up to five metric tons per hour of machining chips. Vortex intensity is adjustable, allowing the system to maintain molten-metal movement when scrap or alloying material is not being charged.

A competitive field

The market includes established suppliers. ABB supplies AL-EMS electromagnetic stirring for aluminum melting, holding and alloying furnaces and reports more than 430 installations; in April 2026 it announced an Arconic order for a fifth stirrer at a Hungarian casthouse. Presezzi Extrusion Group offers the L.E.C. Stirrer for melting and holding furnaces. Pyrotek provides electromagnetic pump systems and LOTUSS scrap submergence, while Rockwell Automation works in adjacent furnace and ladle-shop automation rather than like-for-like permanent-magnet stirring.

Zmag says limited familiarity with the technology is one barrier to wider US adoption. In an August 2025 interview, president Eishin Takahashi said producers globally tend to be conservative and more comfortable with equipment and processes they already know. As casthouses use more challenging recycled feedstock, managing molten-metal movement without immersed mechanical components could become more relevant.